Skip to main content

Interactive antenna lab: see the tradeoffs

Beginner-friendly · No radio needed · Change one setting at a time

There are three ideas that become much easier to understand when you can change the numbers yourself:

  1. Higher radio frequency means a shorter free-space wavelength. Compare HF, CB, VHF, GMRS and 900 MHz LoRa to see why HF antenna elements can be many feet long while LoRa elements are often measured in inches.
  2. Longer coax usually means more signal lost before it reaches the antenna—and after it comes back on receive. The amount depends on cable type and frequency.
  3. Watts and dBm describe the same transmitter power. The toggle changes only the unit you use to enter and view power; it does not alter the radio's output or the cable's percentage loss.

This is a learning tool, not a range calculator, product recommendation, SWR analyzer, or RF exposure compliance calculator.

Change the radio, change the result

Choose a familiar band, then explore a different cable and cable length. This calculator makes an approximation; it does not predict range or certify an installation.

How much power enters the cable?

Use the radio's specified output power. Switch between watts and dBm without changing the actual signal power. Cable loss is a percentage of whatever enters the coax, not a fixed number of watts.

Enter power as

Equivalent power: 158.5 mW = 22.00 dBm

FREQUENCY & ANTENNA SIZE
32.8 cm

One free-space wavelength at 915 MHz

8.2 cm (3.22 in)

One-quarter of a free-space wavelength—a starting concept, not a finished antenna cut length.

FEEDLINE SIGNAL LOSS
1.95 dB

Estimated attenuation for 50 ft of LMR-400 at this frequency

64% remains36% lost in cable
Entering coax22.00 dBm158.5 mW
At antenna feedpoint20.05 dBm101.2 mW

57.3 mW is estimated to be lost as heat along the cable. That is not the same number as 1.95 dB: dB describes the power ratio.

Receiving works in reverse: a −100 dBm signal at the antenna would arrive at the radio at approximately -101.95 dBm, ignoring other losses.

The estimate excludes connectors, mismatch, water damage, antenna gain, and other losses.

About these numbers: Cable labels identify representative manufacturer products, not guaranteed values for every item with the same RG or LMR name. The selected manufacturer's source is linked beside the coax selector. Power is entered in watts or dBm (an absolute level relative to 1 mW); the toggle converts between them without changing the simulated transmitter. Cable loss is measured in dB, a ratio. The cable-only calculation uses 100% of the selected transmitter power at the start of the coax, assumes a nominal matched system, and does not include antenna gain or connector losses. Wavelength uses the free-space speed of light. Cable estimates use published attenuation datapoints for the selected cable, interpolated across adjacent frequencies on a logarithmic frequency scale. Below the first available manufacturer's attenuation datapoint, the lab uses a published Times Microwave LMR attenuation equation where available, or an approximate square-root frequency scaling from the first data point for other products; the screen flags these estimates. Above the last published datapoint the nearest value is held as an approximation. At 915 MHz, some LMR tables end at 900 MHz. The cable-only estimate assumes a matched system: for RG-6, that means 75-ohm equipment, not a typical 50-ohm radio. Installed cable assemblies can vary. Neither free-space quarter wavelength nor cable-only loss predicts antenna efficiency, SWR, gain or communication range. See the manufacturer's LMR catalog.

HF and Technician-class amateur-radio examples​

High frequency (HF) generally spans 3 to 30 MHz. To introduce HF without implying every mode is available to every licensee, the lab includes two examples that lie within privileges available to U.S. Technician-class licensees:

Example presetBandTechnician privilege in this frequency segment
7.030 MHz40 metersCW (Morse code) only; Technician segment 7.025–7.125 MHz
28.400 MHz10 metersSSB voice or CW; Technician segment 28.300–28.500 MHz

The two presets illustrate different antenna scales: 40 meters shows a much longer wavelength, while 10 meters provides a starting point for learning about Technician HF voice privileges.

Important: Choosing a frequency in this lab does not grant permission to transmit. U.S. amateur operating privileges depend on license class, frequency, emission type and applicable FCC rules. Refer to the ARRL frequency allocation summary or ARRL Technician privileges chart. The lab is an antenna and feedline learning tool, not a transmitter compliance calculator.

HF cable-loss estimates deserve special care​

Some of the cable manufacturers publish attenuation tables beginning at 10, 25 or 30 MHz. Rather than incorrectly displaying the 30-MHz loss as though it were measured at 7 MHz, the lab now handles low-HF estimates as follows:

  • LMR-195, LMR-240, LMR-400 and LMR-600: use the manufacturer's published attenuation equation below the first listed datapoint.
  • Other cables with missing low-HF table values: estimate using approximate square-root-of-frequency scaling from the nearest low-frequency published datapoint.
  • RG-213 and HELIAX: include additional published low-frequency datapoints where available.

A notice appears when the selected frequency is below the cable's lowest listed specification. These estimates are for learning and comparison, not a substitute for the exact manufacturer's data, a measured installed cable assembly, or antenna-system matching.

Understanding power: watts, dBm and dB​

What is the baseline? The calculator assumes 100% of the transmitter's selected power enters the coaxial cable. It then estimates what reaches the antenna feedpoint after cable attenuation. It does not assume a fixed transmitter wattage: you choose the input power.

  • measure actual power. A watt is 1,000 milliwatts (mW).
  • is another way to express an absolute power level, relative to 1 milliwatt. 0 dBm = 1 mW; 30 dBm = 1 W.
  • , without the “m,” describes a ratio. A 3 dB loss is approximately half the power, whatever the starting wattage.

The mathematical conversion is: dBm = 10 × log₁₀(power in milliwatts). The reverse is watts = 10^((dBm − 30) / 10).

Power in wattsApproximate dBmExample use
0.025 W (25 mW)14 dBmLow-power LoRa
0.100 W (100 mW)20 dBmLoRa
0.158 W (158 mW)22 dBmLoRa
1 W30 dBmLow-power handheld
5 W37 dBmHandheld
25 W44 dBmMobile/base
50 W47 dBmVHF mobile

The example powers are educational, not recommendations or statements of permitted output for a particular license or radio service.

A simple power-through-cable example​

Suppose 50 feet of the selected coax has 1.95 dB attenuation:

  • Enter 1 watt (30 dBm). Approximately 0.638 W (28.05 dBm) reaches the antenna feedpoint.
  • Enter 0.158 W (22 dBm). Approximately 0.101 W (20.05 dBm) reaches the feedpoint.
  • In both cases, 63.8% of the input power remains, and the same 1.95 dB is lost in the cable.

The watts lost differ because the starting power differs; the percentage and dB attenuation do not. The antenna may then radiate the accepted energy with its own efficiency and directional pattern, which this calculator does not model.

Four experiments to try​

Experiment A: Frequency changes antenna dimensions​

Keep everything else unchanged and compare 7.030 MHz (40-meter HF), 28.400 MHz (10-meter HF), 27.185 MHz (CB), 146 MHz (amateur VHF), 462 MHz (GMRS), and 915 MHz (LoRa). Watch the quarter-wavelength change. The lab automatically displays larger HF dimensions in meters and feet.

At 7.030 MHz, the free-space wavelength is roughly 42.6 meters (140 feet), and a quarter wavelength is roughly 10.7 meters (35 feet). At 915 MHz, the free-space quarter wavelength is only about 8.2 centimeters (3.2 inches). These are wavelength fractions, not instructions to cut an antenna element to an exact physical length.

Why is that useful? It gives you an intuition for why antennas are engineered for particular frequencies instead of being universally interchangeable. Real antenna dimensions also depend on ground plane, loading, matching and construction.

Experiment B: Cable length changes power delivered​

Choose 915 MHz and LMR-400. Compare a 10-foot run, 50-foot run and 100-foot run.

What changed? Only cable attenuation. The displayed “percent remaining” is a power ratio at the far end of the cable, not a predicted fraction of messages received.

Experiment C: Switch between watts and dBm​

Choose the LoRa · 22 dBm preset. Note the input and feedpoint values. Switch the unit selector to Watts (W): the input becomes approximately 0.158 W, but the percentage remaining and power delivered at the antenna stay the same. Select a 25 W or 50 W radio example and repeat.

Next, hold cable length fixed and increase transmitter power. The wattage lost in the cable grows, but the dB loss stays unchanged. The slider uses a logarithmic power scale so it can cover everything from 1 mW to 100 W without crushing LoRa power levels into one end of the scale.

Experiment D: Cable type changes the tradeoff​

Keep frequency and length fixed. Try RG-58, RG-8X (Mini-8), RG-213, LMR-195, LMR-240, LMR-400, LMR-600, and 1/2-inch HELIAX.

At around 915 MHz, compare a long RG-58 run against LMR-400 or HELIAX. At 27.185 MHz, compare typical CB coax options. The differences in cable-only attenuation are often smaller at CB frequencies than at 900 MHz.

Why does the result change? These cables have different construction and attenuation characteristics. Lower-loss cable can be larger, more expensive, stiffer and harder to terminate. The physically largest cable is not automatically the best choice for your station.

Experiment E: Why is RG-6 marked 75 ohms?​

Select RG-6 (Belden 1694A). Notice the warning in the calculator. Its attenuation specification can be compared with 50-ohm coax, but RG-6 is 75-ohm cable and its calculated delivered-power figure assumes a matched 75-ohm system.

Most MeshCore/Meshtastic, GMRS, CB, and amateur VHF/UHF transmitters are designed around nominal 50-ohm antenna systems. Connecting 75-ohm cable between 50-ohm equipment can introduce reflections and mismatch effects not shown by this simple calculator; connectors and suitable matching arrangements matter too. Do not interpret a low RG-6 loss number as a recommendation to replace your radio's specified 50-ohm feedline with RG-6.

Which cable specifications does the lab use?​

Each selection is tied to one specific manufacturer's published cable data, not a guarantee that every manufacturer's version of an RG-style cable performs identically.

Lab selectionRepresentative manufacturer / modelNominal impedance
RG-58Belden 824050 Ω
RG-8X / Mini-8Belden 925850 Ω
RG-213Belden 826750 Ω
RG-6Belden 1694A75 Ω
LMR-195Times Microwave LMR-19550 Ω
LMR-240Times Microwave LMR-24050 Ω
LMR-400Times Microwave LMR-40050 Ω
LMR-600Times Microwave LMR-60050 Ω
1/2-inch HELIAXCommScope/Andrew LDF4-50A50 Ω

The calculator interpolates between published attenuation figures for each selected cable. Below the first available datapoint, it uses the manufacturer's published attenuation formula for certain LMR cables or a flagged approximate square-root frequency extrapolation for other cables. Above the highest datapoint, it uses the nearest listed value (an approximation). For example, a 915 MHz setting may reuse a 900 MHz LMR datapoint. These are educational estimates, not measurements of a finished installed feedline.

Why include both RG-58 and RG-8X? RG-58 is sold in off-the-shelf CB assemblies, including truck-radio installations. RG-8X (Mini-8) is another familiar CB and amateur option. Using real manufacturer reference models helps visitors see why the label on the cable matters more than how thick or familiar it looks.

Five limitations you should understand​

  • Wavelength isn't a cut guide. A nominal quarter wavelength in free space is not necessarily the physical length of a working whip.
  • Coax loss is one piece of the path. This estimate is the cable-only attenuation for a nominal matched system; it doesn't account for mismatched antennas, adapters, connectors or environmental damage. RG-6 is the 75-ohm exception to the predominantly 50-ohm selection list.
  • Gain is directional. Adding an antenna's dBi rating to a link budget requires knowing the pattern in the actual direction of interest.
  • Receiver performance matters. Noise, interference, radio sensitivity and protocol settings still affect decodability.
  • Range cannot be determined from these numbers alone. Terrain and elevation often matter more than simple numerical comparisons.

Continue learning: Gain and patterns, feedline and SWR, or choosing an antenna.

Sources​

Have a result you want to compare against an actual installation? Discuss your setup and measurements in our forum.