Skip to main content

Part 3: feedline, impedance, SWR and loss

The question: Why does a 50-foot cable matter when the antenna has plenty of gain?

Because the signal has to travel through the cable before it reaches the antenna—and the much weaker incoming signal must travel through it again on receive. Some of that RF energy is lost along the way.

What is feedline?​

is the transmission line between the radio and the antenna. Common radio feedline is , made of a center conductor, insulating dielectric, surrounding shield and outer jacket.

Different coax types have different attenuation (loss), flexibility, shielding, weather resistance, connector compatibility and maximum safe power.

Many modern VHF/UHF/900-MHz radio systems use nominal 50-ohm feedline and antennas. A 75-ohm TV cable is not automatically interchangeable just because an adapter can be fitted.

What do coax loss figures mean?​

Manufacturers often specify attenuation in dB per 100 feet at several frequencies. Higher frequencies usually experience greater cable loss in the same cable.

Here is an illustrative example based on the manufacturer's published standard Times Microwave LMR-400 data:

FrequencyCatalog attenuation / 100 ftApprox. loss for 50 ft
150 MHz1.5 dB0.75 dB
450 MHz2.7 dB1.35 dB
900 MHz3.9 dB1.95 dB

Important: These are LMR-400 cable-only estimates at the catalog's stated conditions, not measured results for your installed assembly. Connector losses, adapters, mismatches, weathering and frequency differences add uncertainty. Other cables, including products marketed as LMR-400-type, may have different performance.

At around 900 MHz, 50 feet of this coax loses roughly 1.95 dB, so approximately 64% of the power entering the cable reaches its other end before connector/mismatch losses. A 22 dBm radio is not magically still delivering 22 dBm at the antenna after that cable.

On receive, the signal from the antenna suffers cable attenuation on the way to the receiver too. Loss before the receiver can be particularly damaging for weak-signal reception.

A 3 dB loss consumes approximately half the power. A cable's attenuation is not the same as a failure or a receiver that is necessarily deaf, but it can erase valuable link margin.

Does an antenna's gain cancel cable loss?​

To make an illustrative directional link-budget comparison, add dB gains and subtract dB losses.

Example:

  • Antenna gain, toward the target: +5 dBi.
  • Cable attenuation: −2 dB.
  • Result relative to an ideal isotropic reference, ignoring other losses: +3 dBi.

That is not a prediction of range, and not a complete RF exposure or power-compliance calculation. It just shows why antenna gain and feedline attenuation belong in the same budget.

A 5 dBi antenna mounted directly at the radio and the same antenna on a long coax run are not equivalent installations.

What is impedance?​

describes how a component opposes alternating electrical current and includes resistance and reactance. It depends on frequency.

A radio designed for a 50-ohm load is intended to work with a suitably matched antenna system. If the actual load differs, some incident energy can reflect, resulting in standing waves.

SWR (standing wave ratio)​

describes the ratio of maximum to minimum voltage magnitude along a transmission line due to reflection. A perfectly matched, ideal 50-ohm system has a 1:1 SWR.

Some useful examples for an ideal, lossless line:

SWR at the antenna endApprox. fraction of incident power reflected
1.0:10%
1.5:14%
2.0:111%
3.0:125%

These percentages do not imply the rest is radiated. Accepted power can still be wasted as heat in a lossy or badly designed antenna.

Low SWR is good evidence of a match, not proof of radiation efficiency. A dummy load is a classic counterexample: it can match 50 ohms wonderfully while intentionally turning the energy into heat.

Why an SWR reading at the radio can mislead you​

A lossy coaxial cable attenuates the reflected wave as it returns, so the SWR measured at the radio can appear better than the actual mismatch at the antenna. Longer cable doesn't repair the antenna; it can hide the problem.

A tuner may also make the radio see a good match without fixing high SWR on the feedline beyond the tuner. The details depend on the line type and arrangement.

NanoVNA, SWR meter or power meter?​

  • Antenna analyzer / VNA: can measure impedance, reflection (S11), and VSWR over frequency. Calibrate correctly at the measurement reference plane; a sweep at the radio end includes cable effects.
  • SWR meter: useful for determining whether the transmitter sees a reasonable match, within the meter's supported frequency and power range.
  • Through-line power meter: helps measure forward and reflected power where properly installed.
  • Field strength / comparison reports: show actual on-air performance, though environment and other variables must be controlled.

S11 is a reflection measurement; it does not directly measure radiated efficiency, antenna gain, or coverage.

Connectors are part of the RF path​

A coax assembly is only as good as its connections.

  • SMA, RP-SMA, N-type, BNC, UHF-type, etc. name different connector families. Similar-looking or screw-fitting connectors are not necessarily compatible. Pay special attention to center-pin gender and reverse-polarity versions.
  • Choose connectors rated for your frequency, installation and weather exposure.
  • Keep adapters to a practical minimum.
  • Use proper strain relief, avoid tight bends, keep water out and follow the cable maker's bend-radius specifications.
  • A wet connector can introduce loss, noise, detuning and intermittent failures.

Never transmit through an unknown, shorted or clearly mismatched antenna system without verifying that your equipment can tolerate the condition. Some radios reduce power; others can be damaged.

How to choose the feedline​

  1. Identify your actual operating frequency.
  2. Measure the real cable run—including service loops and routing, not merely vertical height.
  3. Look up the specific manufacturer's attenuation for the exact cable type, at a suitable frequency.
  4. Estimate the total dB loss, plus connector and mismatch allowances.
  5. Compare alternatives: shorter cable, a lower-loss cable, or moving the radio closer to the antenna.
  6. Account for outdoor durability, lightning protection, shielding, grounding, bend radius and installation cost.

For a low-power mesh node, placing a weatherproofed radio near the antenna and running power or data down the mast can avoid a long RF cable—but brings its own power, water ingress, network and lightning-protection questions.

Try it in the interactive lab​

Change the frequency and cable length in our Antenna Lab. Watch how much signal is lost even when the antenna itself is unchanged.

Sources​

Next: Part 4 — Height, Terrain, Mounting and Safety.